How to waterproof boots: leather, suede and fabric
Adventure AndyMatch the waterproofing to what your boots are made of. Smooth leather takes a wax. Suede, nubuck, fabric and mesh take a spray. Whichever you use, clean the boots first, let them dry, put the waterproofing on and give it time to set. Re-apply when water stops beading on the surface.
For our boot care, that comes down to two products:
| Your boots or shoes | What to use |
|---|---|
| Smooth leather | 2-in-1 Boot Wax |
| Suede or nubuck | Rain Proof |
| Fabric, mesh, canvas or knit | Rain Proof |
| Leather with suede or fabric panels | Rain Proof over the whole upper, or Boot Wax on the smooth leather and Rain Proof on the rest |
| Unsealed or vegetable-tanned leather | Not Rain Proof. Check the care label. |
Waterproofing helps boots shed rain and slush. It can't stop water that comes in over the top of the boot or through a split seam.
Why boots need to be clean first
Wax and spray have to reach the material itself. If mud, dust or salt is sitting on the surface, the coating goes on over the dirt, seals it in and ends up patchy.
Brush off loose dirt and wipe the boots with a damp cloth. Then clean them with 1-2 pumps of Boot Soap on a soft cloth. It cleans leather, suede and nubuck, lifts dirt and salt without matting suede, and is safe on canvas and synthetics. Let the boots dry in a cool place, away from heat, before you seal them. For the full routine, see how to clean and condition leather boots and how to clean suede shoes and boots.
How to waterproof leather boots with beeswax
2-in-1 Boot Wax is a leather boot conditioner and waterproofing in one, made with beeswax and lanolin. It feeds dry leather and seals out rain and salt.
- Start with clean boots that have dried completely.
- Warm the wax into a paste by rubbing it in circles with a rag.
- Use the rag to apply it generously and evenly, with extra on the seams.
- Let the boots dry for 24 hours before you wear them.

Test on a small area first. The leather darkens when the wax goes on and lightens as it dries.

Boot Wax also works on suede and synthetics. On suede, nubuck and woven fabric, though, Rain Proof is the better match.
How to waterproof suede shoes with a protector spray
Rain Proof is a waterproofing and stain protector spray for shoes, made for suede, fabric and mesh. It also works on nubuck, canvas, cotton, nylon, knit and leather. It's also safe on hats, bags, jackets and jeans.
- Start with shoes that are clean and completely dry. On suede and nubuck, brush the nap up once they're dry.
- Hold the bottle upright, 5-8 inches (13-20 cm) from the shoe.
- Spray evenly over the whole surface. Keep the bottle moving so no spot gets soaked.
- Apply a second coat.
- Let it dry completely before the shoes meet water or dirt.

Rain Proof isn't for unsealed or vegetable-tanned leather. If you aren't sure how your leather was finished, check the care label before you spray, and test a hidden spot either way.
How to waterproof hiking boots
Most hiking boots mix materials, often leather or nubuck with fabric panels and mesh. Rain Proof works on all of those, so the simplest route is to clean the boots and spray the whole upper. If yours are mostly smooth leather, wax the leather and spray the fabric. Either way, give the seams and the stitching around the tongue extra attention, because that's where water usually finds a way in.
How to tell when to re-apply
Waterproofing wears down with use. To check it, flick a few drops of water onto the boot.
- If the water beads up and rolls off, the coat is still doing its job.
- If it darkens the surface and soaks in, it's time to clean the boots and re-apply.
The toes and the creases across the top of the foot usually go first, so check there. Test after a wet week, and before any trip where your feet will get wet.
A set for each kind of boot
The Boot Revival Set comes in two versions. The smooth leather set has Boot Soap, 2-in-1 Boot Wax and Boot Medic. The suede, nubuck and woven set has Boot Soap, Rain Proof and Boot Medic. The order is the same for both: clean with Boot Soap and let the boots dry, seal them, then freshen the inside with Boot Medic overnight whenever they need it. You'll find each product on its own in our boot care collection.
Questions people ask
Does beeswax waterproof boots?
Beeswax helps leather shed water. 2-in-1 Boot Wax pairs it with lanolin, so one coat seals out rain and salt and feeds dry leather at the same time. Re-apply when water no longer beads on the leather.
Can I use a waterproof spray on leather boots?
Rain Proof works on leather, except unsealed or vegetable-tanned leather. On smooth leather, Boot Wax works best and conditions the leather as well.
How do I protect new suede shoes?
Give them two coats of a suede protector spray like Rain Proof before you wear them, and let it dry completely before they meet water or dirt.
How long does waterproofing take to dry?
Give Boot Wax 24 hours. Let Rain Proof dry completely before the shoes meet water or dirt.
Which laces hold up in wet boots?
Unbreakable Boot Laces are made of UHMWPE fiber, which doesn't absorb water, so the laces won't rot or freeze. See all our hiking boot laces.